Baumuller包米勒BUS622-15驅動器2726/2749代碼講解

更新時間：2023-11-30

點擊次數：1217

2726：Cam generator - the active cam cannot be used in this mode
凸輪生成器-活動凸輪不能在此模式下使用
In the "parameter-controlled processing" mode the cyclical processing is selected.
在“參數控制處理"模式中，選擇循環處理。

10.31鮑米勒驅動器1.jpg

The count of supporting points must accord to power
支撐點的數量必須符合權力
This is not the case at the active cam (e.g. count of supporting points is 256, 512 or 1024)
主動凸輪的情況并非如此（例如，支撐點的數量為256、512或1024）

10.30鮑米勒驅動器3.jpg

2749：Cam file version is unknown凸輪文件版本未知
The controller firmware doesn't know the version of the transmitted cam file.
控制器固件不知道傳輸?shù)耐馆單募陌姹尽?/p>

10.30鮑米勒驅動器5.jpg

Consequence: 后果：
The cam file is rejected.
凸輪文件被拒絕。

7.21鮑米勒驅動器2_副本.jpg

Baumuller鮑米勒驅動器BUS6-MC-00-S000-3051-SI00-0000 M Drive，
鮑米勒伺服器BUM62T-100/130-54-M-039 BUM62T-100-130-54-M-039，
鮑米勒驅動器BUM64F-300/390-54-E-M-211 BUM64F-300，
Baumuller驅動器BUM63TS-210/235-54-E-M-011 BUM63TS-210，
Baumuller鮑米勒驅動器BM4454-ZI6-01245R05-0309 BM4454，
鮑米勒驅動器BUM60-08/16-54-B-001 BUM60-VC-0A-0001，

6.27鮑米勒伺服驅動器.jpg

報業印刷專用包米勒驅動器BUM62T-100 130-54-M-034 能測試維修，
鮑米勒驅動器BUM63S-150/195-54-O-O-005 BUM63S-150-195，
鮑米勒伺服器BM4423-SI1-21208-0308 KBA印刷機專用，
Baumuller鮑米勒驅動器板卡3.0007A 3.9405D 3.0016C，
包米勒驅動器BM4423-ST1-01242-0309 Baumuller，
Baumuller鮑米勒驅動器BM4-03維修，
Baumuller 包米勒驅動器BUG623-56-54-E-013，
印刷設備常用包米勒驅動器BM4-03，
Baumuller驅動器BUS622-15/22-54-M-202能測試維修
Bau+A41.0121L BM4434 BM4433 BM4432，
Baumuller鮑米勒驅動器BM4443-SI1-01200-03 可測試維修，